Get quotes

Cable and voltage drop calculator

Enter the system voltage, the total load and the cable length to see the voltage drop, the cable size you need and the transformer or driver to buy.

Voltage drop on a lighting cable

System voltage
W
Add up the watts of every light on this run.
m
Where the lights are

Result

Voltage drop–
Volts lost–
Voltage at the lights–
Current–
Smallest cable within 5%–
Longest run on this cable at 5%–
Transformer or driver–

Every metre of cable loses a little voltage. On a 230 V circuit that hardly matters over a garden, but on a 12 V system the same loss can leave the last spotlights dim, flickering or not lighting at all. Low-voltage garden lighting needs thicker cable, shorter runs or a higher voltage than most people expect.

How voltage drop is worked out

Voltage drop (V) = current (A) × cable length (m) × mV/A/m for the cable size ÷ 1,000

The current is the load in watts divided by the voltage (and by a power factor of 0.9 for 230 V LED drivers). The mV/A/m figure is the drop per amp per metre of two-core copper cable, which already counts the trip out and back: 18 mV/A/m for 2.5 mm², 29 for 1.5 mm² and 44 for 1 mm².

When the lights are spread evenly along the cable rather than all at the end, the average current over the run is about half, so the drop is roughly halved. The calculator lets you choose either.

How much drop is acceptable

SANS 10142-1, the South African wiring code, limits voltage drop on a final circuit to 5% of the supply voltage: 11.5 V on 230 V. For 12 V and 24 V LED lighting, aim for 5% (0.6 V at 12 V) for even brightness; up to 10% works with drivers and lamps rated for a wide input range, but the far lights will be dimmer.

If the drop is too high, use thicker cable, split the lights onto two or three shorter runs fed from the middle, move the transformer closer to the lights, or go to 24 V, which halves the current and cuts the drop to a quarter for the same cable.

Sizing the transformer or LED driver

Add up the watts of every light on the transformer and allow at least 25% headroom, then choose the next standard size up. A driver run flat out runs hot and fails early, especially in a closed box in the sun. Use a driver rated IP67 outdoors or keep it in a ventilated, weatherproof enclosure, and match the type to the lamps: constant-voltage 12 V or 24 V for most garden spotlights and LED strip.

See garden lights and outdoor LED strip lights for low-voltage systems.

Wiring outdoor lights safely

New 230 V outdoor circuits, and the plug point or isolator a garden transformer connects to, must be installed by a registered electrician, who issues a Certificate of Compliance (CoC). Underground 230 V cable must be armoured (SWA) or in conduit at the right depth, on an earth-leakage protected circuit. Low-voltage cable from the transformer can be shallower, but bury it at least 150 mm deep or in conduit where you dig. Ask for quotes from outdoor lighting electricians.

Frequently asked questions

What size cable do I need for 12 V garden lights?
It depends on the load and the length. As a guide, 40 W at 12 V over 15 m with the lights spread along the cable needs 2.5 mm² to stay within 5%. Over 25 m the same load needs 4 mm², or split the run, or change to 24 V.
Why are my last garden lights dimmer?
Almost always voltage drop: the cable is too thin or too long for the load, so the lights at the far end get less voltage. Check the result in the calculator, then use thicker cable, feed the run from the middle or add a second run from the transformer.
Is 24 V better than 12 V for garden lighting?
For long runs, yes. At 24 V the same lights draw half the current, so the voltage drop is a quarter of the percentage at 12 V on the same cable. Your lamps and driver must all be rated for 24 V.
How big should my LED transformer be?
Add the watts of all the lights and add 25% or more: 48 W of lights need at least a 60 W driver. Choose the next standard size up and use an IP67-rated driver outdoors.

More outdoor lighting tools

Results are estimates for planning and comparing quotes. They don't replace a site visit, a lighting design or an electrician's calculation to SANS 10142-1.

Get outdoor lighting quotes

List the fittings you have in mind, or just describe the job. Suppliers and electricians who work in your area quote you directly. Free, no obligation.

Fixture schedule

RefFitting, finish or modelQtyPowerRemove
L1
L2
L3
Up to 20 lines. Not sure what you need? Leave this empty and describe the job.

No fittings yet

Free and no obligation. By sending you agree that we may share your request with a suitable supplier or electrician. See our privacy policy.

Get free lighting quotes